Safety yellow

The strong yellow that means CAUTION, defined by an American standard as Munsell 5Y 8/12.

Overview

Safety yellow is the yellow of CAUTION signs, of the stripes painted on steps, ledges and low beams, and of the labels on oxidizing chemicals. Its usual web code is #EED202: red and green both strong, green a little lower, and almost no blue. On screen it is a strong, slightly warm yellow, between gold and dandelion.

Like safety orange, it is set by a standard. ANSI Z535.1 gives safety yellow as Munsell 5Y 8/12: a pure yellow hue, a very light value of 8 on a scale of 10, and a strong chroma of 12. The federal color charts for hazardous-materials labels use the same notation and pin it down in CIE numbers. Unlike safety orange, this yellow sits right at the edge of what a screen can show, and our conversion, about #ECC800, lands close to the web code: a shade darker and a touch more orange.

What the yellow means depends on the system. In the American sign system it is the mildest of three signal colors: CAUTION, below WARNING orange and DANGER red. OSHA’s own color code makes yellow the color of caution and of hazards you can trip over, fall from or get caught between. In the international system, ISO 3864, yellow is the color of every warning sign, with a black symbol in a yellow triangle. On American roads, yellow marks warning signs and the center lines between opposing lanes.

On screens, safety yellow is very light. Black text reads extremely well on it (almost 14:1), which is why black and yellow is the classic hazard pairing. White text reaches only about 1.5:1 and should never be used on it; for white lettering, use a dark olive shade instead.

HEX#EED202
RGBrgb(238, 210, 2)
HSLhsl(53, 98%, 47%)
HSV53°, 99%, 93%
CMYK0, 12, 99, 7
OKLCHoklch(86.1% 0.178 99.5)
Every code converts from the HEX value #EED202. #EED202 is the code Wikipedia’s “Shades of yellow” gives for safety yellow, citing ANSI Z535, but the standard itself gives no hex and we could not trace how that code was worked out. ANSI defines safety yellow as Munsell 5Y 8/12 (Munsell Color), the notation the US hazardous-materials label rules give as CIE x 0.4562, y 0.4788 and luminance factor 59.10% under illuminant C. Our conversion of that point to sRGB is about #ECC800, close to the web code. Federal Standard 595C chip 13655, listed as OSHA safety yellow in Aubrey Jaffer’s transcription, converts to a more orange yellow, about #FFBB00. CMYK is a screen-based estimate; print results vary.
Safety yellow color card, hex #EED202: “Caution: may cause staring”

Safety yellow on the color map

The ANSI value sits just below the reference and a hair to the left: a little darker and very slightly more orange. The ISCC-NBS vivid yellow centroid sits beside it, a step further left. The federal chip listed as OSHA safety yellow lies furthest left, near the edge of the outline: a warmer, more orange yellow. The outline is an approximate range, not a measured one.

Shades and tints

Tints with white

Shades with black

Tones with gray

Safety yellow sits in the middle. Tints add white, shades add black and tones add gray, in 10% steps out from it. Tap any swatch to copy its code.

Light and dark safety yellow

#F8ED9A
Pale safety yellowMixed 60% with white. A soft butter for backgrounds.
#F5E467
Light safety yellowMixed 40% with white. A clear lemon cream.
#EED202
Safety yellowThe reference color.
#ECC800
ANSI safety yellowThe standard’s Munsell 5Y 8/12 converted to sRGB. A shade darker and warmer; black text reads well on it (about 12.8:1).
#FFDF00
Golden yellowLighter and a little warmer: a separate named color with a page of its own. See golden yellow
#776901
Dark safety yellowMixed 50% with black. A deep olive that holds white text (about 5.5:1).
#5F5401
Deep safety oliveMixed 60% with black. Good for white lettering (about 7.6:1).

Colors that go with safety yellow

Pairings that work in rooms, outfits and interfaces.

Caution sign

The ANSI CAUTION panel: black letters on safety yellow, above a white message area.

Hazard stripes

Yellow and black bands, the way edges, steps and low beams are marked. Keep text black on the yellow.

Road warning

A yellow diamond sign against asphalt gray, with a white edge line. Black carries any text on the yellow.

Radiation sign

A purple trefoil on yellow, the pairing US rules allow for the radiation symbol. Purple reads well on yellow.

Safety yellow and navy

Yellow and navy are near opposites. Navy carries the text and steadies the yellow.

Butter to olive

One hue from pale to dark. Bright but calm, and easy to keep legible.

Color-wheel palettes

Pick a palette to see where its colors sit on the color wheel. The caret marks safety yellow. Tap a band to copy its code.

Similar colors

Sunflower80%Saffron79%Gold85%Banana yellow76%Golden yellow79%Safety yellowDandelion82%

Lined up by hue around safety yellow. Hover a color to see how similar it is.The bar under each name shows how similar it is. Similarity comes from the distance between the two colors in OKLab, a model of how we see color.

Safety yellow vs safety orange

Safety yellow#EED202 · hue 53°
  • Much lighter
  • Means CAUTION on ANSI signs
  • Defined as Munsell 5Y 8/12
Safety orange#FF7900 · hue 28°
  • Darker and redder
  • Means WARNING, a step more serious
  • Defined as Munsell 5YR 6/15

Meaning

  • CAUTION signs
  • Trip and fall hazards
  • Road warnings
  • ISO warning signs

Safety yellow is a color with a job, but the job changes with the rulebook. American signs use it for CAUTION, the mildest hazard level; OSHA uses it for things you can trip over or fall from; international signs use it for every warning. Studies of color and emotion test basic words like “yellow”, not safety yellow, so the claims here are about rules and standards, not mood.

Yellow means CAUTION

Standard

ANSI Z535.4 says “The word CAUTION shall be in safety black letters on a safety yellow background”. CAUTION is the lowest of the three hazard signal words, below WARNING on orange and DANGER on red. The chair of the Z535.1 subcommittee explains that the orange has to look clearly orange so it is never confused with the yellow of caution.1

OSHA’s color for physical hazards

Federal rule

OSHA’s own safety color code names just two colors. Red is for danger and stop, and “Yellow shall be the basic color for designating caution and for marking physical hazards such as: Striking against, stumbling, falling, tripping, and ‘caught in between.’” Its caution signs have a yellow background and a black panel with yellow letters, matched to the ANSI color tables.2, 3

Internationally, yellow means any warning

Standard

ISO 3864-1, the international design standard for safety signs, gives warning signs a yellow safety color, a black contrast color and a black symbol, inside an equilateral triangle with rounded corners. Its examples include hot surfaces, biological hazards and electricity. So where an American label grades a hazard as CAUTION, an ISO sign uses yellow for all of them.4

The background of hazard labels

Federal rule

US shipping rules require a yellow background on the OXIDIZER label, and the color charts used to check labels center that yellow on Munsell 5.0Y 8.0/12, the same notation as ANSI safety yellow. Separately, US radiation rules require the radiation symbol to be magenta, purple or black on a yellow background.5, 6, 7

Chosen first for visibility

Historical record

A 1924 report by the American Association of State Highway Officials favored yellow for all danger and caution signs, even STOP, because of its superior visibility, and rejected red as too hard to see at night. Red returned for STOP only in 1954, once fade-resistant finishes made it visible after dark.8

Sources (8)
  1. Earley, E. (2023, July 1). “ANSI Z535.1 – Safety Colors in Focus”. In Compliance Magazine, quoting ANSI Z535.4, section 7.2.3, and Angela Lambert, chair of the ANSI Z535.1 subcommittee.
  2. Code of Federal Regulations, 29 CFR 1910.144, “Safety color code for marking physical hazards”, paragraph (a)(3), via Cornell Law School’s Legal Information Institute.
  3. Code of Federal Regulations, 29 CFR 1910.145, “Specifications for accident prevention signs and tags”, paragraph (d)(4), via Cornell Law School’s Legal Information Institute.
  4. International Organization for Standardization, ISO 3864-1:2011, Graphical symbols – Safety colours and safety signs – Part 1: Design principles for safety signs and safety markings, Table 1 (sample pages via iTeh Standards).
  5. Code of Federal Regulations, 49 CFR 172.426, “OXIDIZER label”, via Cornell Law School’s Legal Information Institute.
  6. Code of Federal Regulations, 49 CFR Part 172, Appendix A, “Office of Hazardous Materials Transportation Color Tolerance Charts and Tables”, table 1 (yellow: 5.0Y 8.0/12, Y 59.10, x .4562, y .4788), via Cornell Law School’s Legal Information Institute.
  7. Code of Federal Regulations, 10 CFR 20.1901, “Caution signs”, via Cornell Law School’s Legal Information Institute.
  8. Federal Highway Administration, “The Evolution of MUTCD”, mutcd.fhwa.dot.gov.

History

Yellow became a caution color on American roads in the 1920s, decades before it had a Munsell number. The road manuals, the workplace rules and the shipping rules each took it up in their own way.

  1. 1924

    The First National Conference on Street and Highway Safety proposes standard colors for traffic devices: red for stop, green for proceed, and black letters on yellow for caution.1

  2. 1924

    A report by the American Association of State Highway Officials recommends a yellow background for all danger and caution signs, including STOP, because yellow is easier to see. Red is rejected as too hard to see at night.1

  3. 1935

    The first Manual on Uniform Traffic Control Devices keeps the STOP sign black on yellow, or yellow on a red octagon. Center lines may be white, yellow or black, whichever contrasts best.1

  4. 1954

    A revision of the traffic manual makes STOP signs white on red, thanks to new fade-resistant finishes, and introduces the YIELD sign as a black-on-yellow triangle.1

  5. 1971

    The rewritten fifth edition of the traffic manual makes yellow the color of the markings that separate opposing traffic.1

  6. December 20, 1991

    A federal amendment gives the hazardous-materials label rule its current wording: the background of the OXIDIZER label must be yellow.2

  7. 2011

    ISO 3864-1 is republished. Its table of sign types keeps yellow, with black, for all warning signs, in a triangle with rounded corners.3

  8. June 13, 2013

    OSHA lets employers match the yellow of caution signs to Table 1 of ANSI Z535.1-2006 (reaffirmed 2011), as well as the older Z53.1-1967.4, 5

Sources (5)
  1. Federal Highway Administration, “The Evolution of MUTCD”, mutcd.fhwa.dot.gov.
  2. Code of Federal Regulations, 49 CFR 172.426, “OXIDIZER label” (Amdt. 172-123, 56 FR 66257, December 20, 1991), via Cornell Law School’s Legal Information Institute.
  3. International Organization for Standardization, ISO 3864-1:2011, Table 1 (sample pages via iTeh Standards).
  4. Occupational Safety and Health Administration (2013, June 13). “Updating OSHA Standards Based on National Consensus Standards; Signage”, direct final rule, 78 FR 35559.
  5. Code of Federal Regulations, 29 CFR 1910.145, paragraph (d)(4), via Cornell Law School’s Legal Information Institute.

Safety yellow in use

All brand colors
#ECC800#262626
Safety signANSI CAUTION signs and labels

American safety signs and product labels put the word CAUTION in black on a safety yellow panel. The standard defines the yellow as Munsell 5Y 8/12, about #ECC800 on screen, and safety black as Munsell N 1.5, about #262626.

#ECC800#262626
Source: ANSI Z535 / Munsell
#ECC800#000000
Hazard labelUS oxidizer labels

Federal hazardous-materials rules say the OXIDIZER label must have a yellow background, with a black flame-over-circle symbol. The color charts used to check labels center that yellow on Munsell 5.0Y 8.0/12: about #ECC800 on screen.

#ECC800#000000
Source: 49 CFR Part 172

Logos belong to their owners and are shown unaltered, only to show where each palette comes from. Palettes are sampled in-house.

Questions

What color is safety yellow?

A strong, slightly warm yellow used for caution. Its usual web code is #EED202 (RGB 238, 210, 2). The ANSI standard defines it as Munsell 5Y 8/12, which on screen is about #ECC800, a shade darker.

Who defines safety yellow?

ANSI Z535.1, the American standard for safety colors. It gives safety yellow as a Munsell notation, 5Y 8/12, with CIE color coordinates, not as a hex code. The hex #EED202 comes from Wikipedia, not from the standard.

What does safety yellow mean on a sign?

On American ANSI signs it means CAUTION, the mildest of the three hazard levels: black letters on yellow. Orange means WARNING and red means DANGER. On international ISO signs, yellow is used for every warning, in a triangle with a black symbol.

What does OSHA say about yellow?

OSHA’s color code makes yellow the basic color for caution and for marking physical hazards such as striking against, stumbling, falling, tripping and getting caught in between. Its caution signs have a yellow background and black lettering.

Is safety yellow the same as school bus yellow?

No. American school buses use their own color, national school bus yellow, which is a deeper, more orange yellow than the caution yellow of safety signs. The two have separate specifications.

Is the yellow on high-visibility vests safety yellow?

Not quite. Vests for road workers use fluorescent yellow-green, a glowing color that standard safety yellow cannot match. That color is closer to neon yellow.

What text color works on safety yellow?

Black, by far. Black text on #EED202 reaches almost 14:1 contrast, while white reaches only about 1.5:1, which is unreadable. For white lettering, switch to a dark olive shade such as #5F5401.

Can a screen show true safety yellow?

Almost exactly. The standard’s CIE values sit right at the edge of the sRGB range most screens use, and convert to about #ECC800, close to the common code #EED202.